platform.dox
5.14 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
/*
ChibiOS/RT - Copyright (C) 2006,2007,2008,2009,2010,
2011,2012 Giovanni Di Sirio.
This file is part of ChibiOS/RT.
ChibiOS/RT is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 3 of the License, or
(at your option) any later version.
ChibiOS/RT is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
---
A special exception to the GPL can be applied should you wish to distribute
a combined work that includes ChibiOS/RT, without being obliged to provide
the source code for any proprietary components. See the file exception.txt
for full details of how and when the exception can be applied.
*/
/**
* @defgroup LPC11xx LPC11xx Drivers
* @details This section describes all the supported drivers on the LPC11xx
* platform and the implementation details of the single drivers.
*
* @ingroup platforms
*/
/**
* @defgroup LPC11xx_HAL LPC11xx Initialization Support
* @details The LPC11xx HAL support is responsible for system initialization.
*
* @section lpc11xx_hal_1 Supported HW resources
* - SYSCON.
* - Flash.
* .
* @section lpc11xx_hal_2 LPC11xx HAL driver implementation features
* - Clock tree initialization.
* - Clock source selection.
* - Flash controller initialization.
* - SYSTICK initialization based on current clock and kernel required rate.
* .
* @ingroup LPC11xx
*/
/**
* @defgroup LPC11xx_GPT LPC11xx GPT Support
* @details The LPC11xx GPT driver uses the CTxxBy peripherals.
*
* @section lpc11xx_gpt_1 Supported HW resources
* - CT16B0.
* - CT16B1.
* - CT32B0.
* - CT32B1.
* .
* @section lpc11xx_gpt_2 LPC11xx GPT driver implementation features
* - Each timer can be independently enabled and programmed. Unused
* peripherals are left in low power mode.
* - Programmable CTxxBy interrupts priority level.
* .
* @ingroup LPC11xx
*/
/**
* @defgroup LPC11xx_PAL LPC11xx PAL Support
* @details The LPC11xx PAL driver uses the GPIO peripherals.
*
* @section lpc11xx_pal_1 Supported HW resources
* - GPIO0.
* - GPIO1.
* - GPIO2.
* - GPIO3.
* .
* @section lpc11xx_pal_2 LPC11xx PAL driver implementation features
* - 12 bits wide ports.
* - Atomic set/reset functions.
* - Atomic set+reset function (atomic bus operations).
* - Output latched regardless of the pad setting.
* - Direct read of input pads regardless of the pad setting.
* .
* @section lpc11xx_pal_3 Supported PAL setup modes
* - @p PAL_MODE_RESET.
* - @p PAL_MODE_UNCONNECTED.
* - @p PAL_MODE_INPUT.
* - @p PAL_MODE_OUTPUT_PUSHPULL.
* .
* Any attempt to setup an invalid mode is ignored.
*
* @section lpc11xx_pal_4 Suboptimal behavior
* Some GPIO features are less than optimal:
* - Pad/port toggling operations are not atomic.
* - Pull-up and Pull-down resistors cannot be programmed through the PAL
* driver and must be programmed separately using the IOCON peripheral.
* - Reading of the output latch for pads programmed as input is not possible,
* the input pin value is returned instead.
* .
* @ingroup LPC11xx
*/
/**
* @defgroup LPC11xx_SERIAL LPC11xx Serial Support
* @details The LPC11xx Serial driver uses the UART peripheral in a
* buffered, interrupt driven, implementation. The serial driver
* also takes advantage of the LPC11xx UARTs deep hardware buffers.
*
* @section lpc11xx_serial_1 Supported HW resources
* The serial driver can support any of the following hardware resources:
* - UART.
* .
* @section lpc11xx_serial_2 LPC11xx Serial driver implementation features
* - Clock stop for reduced power usage when the driver is in stop state.
* - Fully interrupt driven.
* - Programmable priority level.
* - Takes advantage of the input and output FIFOs.
* .
* @ingroup LPC11xx
*/
/**
* @defgroup LPC11xx_SPI LPC11xx SPI Support
* @details The SPI driver supports the LPC11xx SSP peripherals in an interrupt
* driven implementation.
* @note Being the SPI a fast peripheral, much care must be taken to
* not saturate the CPU bandwidth with an excessive IRQ rate. The
* maximum transfer bit rate is likely limited by the IRQ
* handling.
*
* @section lpc11xx_spi_1 Supported HW resources
* - SSP0.
* - SSP1 (where present).
* .
* @section lpc11xx_spi_2 LPC11xx SPI driver implementation features
* - Clock stop for reduced power usage when the driver is in stop state.
* - Each SSP can be independently enabled and programmed. Unused
* peripherals are left in low power mode.
* - Fully interrupt driven.
* - Programmable interrupt priority levels for each SSP.
* .
* @ingroup LPC11xx
*/